Microlife BP A2 Standard Blood Pressure Monitor User Manual

The Microlife BP A2 Standard is an automatic upper arm blood pressure monitor designed for home use. It features one-touch operation, a large LCD display, irregular heartbeat detection, 2-user memory with 30 measurements each, WHO blood pressure classification indicator, date and time display, and an adjustable cuff for arm circumferences 22-32 cm. Powered by 4xAA batteries or optional AC adapter. Below are key sections for safety, features, setup, measurement, memory, maintenance, and troubleshooting.

Features at a Glance

Key components: Main unit with LCD display, Adjustable upper arm cuff, AC adapter port, Battery compartment, START/STOP button, Memory button.

Safety Information

Read all instructions before use. For accurate measurements and safe operation.

1. Consult your physician before using if you have arrhythmia, pre-eclampsia, or other circulatory disorders.
2. Do not use on infants, children, or persons unable to express their will.
3. Do not use while connected to high-frequency surgical equipment or MRI scanners.
4. Measure at consistent times daily, before medication and meals.
5. Avoid eating, smoking, exercising, or bathing 30 minutes before measurement.

WARNING! This device is for home monitoring only, not for diagnosis. Always consult your doctor about your blood pressure.

Package Contents

Unpack and verify all components are present.

• Microlife BP A2 Standard monitor (main unit)
• Adjustable upper arm cuff (22-32 cm)
• Instruction manual (this document)
• 4 x AA batteries (for initial use)
• Storage case

Note: AC adapter is sold separately (Model: AD-10).

Device Overview

Front Panel: LCD display, START/STOP button, Memory (M) button. Rear: Battery compartment, AC adapter port. Cuff: Air tube connector, Velcro closure, artery marker.

Display Symbols: Systolic pressure, Diastolic pressure, Pulse rate, User indicator (1 or 2), Memory full, Irregular heartbeat, Battery low, WHO classification bar, Date and time.

Initial Setup

Prepare device for first use.

1. Insert batteries: Open battery compartment, insert 4 AA batteries observing polarity.
2. Set date and time: Press and hold M button for 3 seconds, use START/STOP to adjust.
3. Select user: Briefly press M button to toggle between User 1 and User 2.
4. Apply cuff correctly: Place cuff on bare upper arm with artery marker over brachial artery.

CAUTION! Do not mix old and new batteries. Remove batteries if device will not be used for extended period.

Taking a Measurement

For accurate results, follow these steps carefully.

1. Sit comfortably with back supported and feet flat on floor.
2. Rest for 5 minutes before measuring.
3. Apply cuff to left upper arm (unless instructed otherwise by doctor).
4. Position cuff so bottom edge is 2-3 cm above elbow.
5. Ensure tube runs down center of arm.
6. Press START/STOP button to begin measurement.
7. Remain still and quiet during inflation and deflation.
8. Results display automatically with WHO classification.
9. Device automatically powers off after 1 minute.

Tip: Take measurements at same time each day for consistent tracking.

Memory Function

Stores 30 measurements per user with date and time.

1. Select user: Press M button to choose User 1 or User 2.
2. View memory: Press M button twice quickly to scroll through stored measurements.
3. Clear memory: Press and hold M button for 5 seconds while in memory mode.
4. Memory full: When 30 measurements stored, oldest is automatically deleted.

Note: Memory is maintained when batteries are replaced (within 5 minutes).

Understanding Results

Interpret your blood pressure readings.

Irregular Heartbeat Symbol: Appears if irregular rhythm detected during measurement. Consult physician if frequent.

Care & Maintenance

Proper care ensures accuracy and longevity.

1. Clean device with soft, dry cloth only. Do not use liquids or solvents.
2. Store in provided case in cool, dry place away from direct sunlight.
3. Remove batteries if device not used for more than 3 months.
4. Replace cuff if it becomes damaged or shows signs of wear.
5. Do not disassemble device. No user-serviceable parts inside.

CAUTION! Never immerse device in water. Do not use near flammable gases.

Specifications

• Measurement Method: Oscillometric
• Pressure Range: 0-299 mmHg
• Pulse Range: 40-199 beats per minute
• Accuracy: Pressure: ±3 mmHg, Pulse: ±5% of reading
• Memory: 2 users x 30 measurements
• Cuff Size: 22-32 cm arm circumference
• Power Supply: 4 x 1.5V AA batteries or 6V DC adapter
• Battery Life: Approximately 500 measurements (alkaline batteries)
• Dimensions: 123 x 85 x 141 mm (main unit)
• Weight: Approximately 300g (without batteries)
• Operating Conditions: 10°C to 40°C, 15% to 90% humidity

Troubleshooting

Reset: Remove batteries for 5 minutes, then reinsert.

Service: For technical support, contact Microlife customer service or visit www.microlife.com