Microlife BP AG1-10 Blood Pressure Monitor User Manual

The Microlife BP AG1-10 is a fully automatic upper arm blood pressure monitor with clinically validated accuracy, featuring one-touch operation, irregular heartbeat detection, Intellisense technology for comfortable inflation, a large LCD display with backlight, memory storage for multiple users, body movement detection, WHO classification indicator, and date/time function. It is powered by 4xAA batteries or optional AC adapter. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main unit with LCD display, Arm cuff with D-Ring, AC adapter port, Battery compartment, START/STOP button, Memory button.

Safety Information

Read all instructions before use. For accurate measurements, follow guidelines carefully.

1. Intended for personal home use only, not for professional medical diagnosis.
2. Do not use on infants, young children, or persons unable to operate the device.
3. Consult your physician before use if you have arrhythmia, pre-eclampsia, or other cardiovascular conditions.
4. Do not use the device near strong electromagnetic fields (e.g., microwave ovens, mobile phones).
5. Keep device and cuff away from heat, moisture, and direct sunlight.

WARNING! Do not use the device if you suspect it is damaged. Never modify the device. Use only Microlife-approved accessories.

Package Contents

Unpack and verify all items are present.

• Microlife BP AG1-10 Blood Pressure Monitor (main unit)
• Arm Cuff (22-32 cm / 8.7-12.6 inches)
• Instruction Manual (this document)
• Quick Start Guide
• Storage Case
• Warranty Card

Note: Batteries and AC adapter are not included in standard package.

Device Overview

Front Panel: LCD Display, START/STOP Button, Memory (M) Button. Side: AC Adapter Socket. Rear: Battery Compartment, Cuff Socket.

Display Symbols: Systolic Pressure, Diastolic Pressure, Pulse Rate, User Indicator (1 or 2), Memory Full, Irregular Heartbeat Symbol, Body Movement Symbol, WHO Classification Bar, Low Battery, Date/Time.

Cuff: D-Ring for easy application, Air Tube with connector, Artery Marker (align with brachial artery).

Initial Setup

Prepare device for first use.

1. Insert Batteries: Open battery compartment on rear, insert 4 AA batteries observing correct polarity.
2. Set Date and Time: Press and hold M button for 3 seconds until date flashes. Use START/STOP to adjust values, M to confirm and move to next setting.
3. Apply Cuff: Sit comfortably with feet flat on floor. Wrap cuff on bare upper left arm 1-2 cm above elbow. Artery marker should align with inner arm. Cuff should be snug but not tight.
4. Rest for 5 minutes before first measurement.

CAUTION! Do not over-tighten cuff. Ensure tube is not kinked.

Taking a Measurement

For most accurate results, measure at the same time each day.

1. Sit comfortably with back supported and legs uncrossed.
2. Place arm on table so cuff is at heart level.
3. Press START/STOP button. Device will inflate automatically.
4. Remain still and quiet during measurement. Do not talk or move arm.
5. Measurement completes when cuff deflates fully. Results display with systolic, diastolic, and pulse rate.
6. Device automatically stores reading (for last user used).
7. To turn off, press START/STOP again or wait 1 minute for auto power-off.

Tip: Avoid eating, drinking caffeine, smoking, or exercising 30 minutes before measurement.

Memory Function

Stores up to 99 readings for each of two users.

1. Select User: Press M button briefly to toggle between User 1 and User 2 (indicator on display).
2. Recall Memory: Press and hold M button for 2 seconds to enter memory mode. Use START/STOP to scroll through stored readings with date/time.
3. Delete All Memory: In memory mode, press and hold M button for 5 seconds until "CLR" appears. Release to delete all readings for current user.
4. Memory Full: When 99 readings are stored, oldest reading is automatically overwritten.

Note: Memory is maintained when batteries are replaced if done within 2 minutes.

Special Features

Irregular Heartbeat Detection: If an irregular pulse is detected during measurement, the irregular heartbeat symbol flashes with result. Consult physician if this occurs frequently.

WHO Classification: After measurement, a bar graph shows where your reading falls according to WHO categories (optimal, normal, high-normal, etc.).

Body Movement Detection: If movement is detected, measurement pauses and movement symbol appears. Remain still to resume.

Intellisense: Technology determines optimal inflation pressure for each user, minimizing discomfort.

Care & Maintenance

Clean device with soft, dry cloth. Do not use solvents or immerse in water.

1. Cuff Care: Wipe with damp cloth and mild detergent if soiled. Do not machine wash or iron.
2. Storage: Keep in provided case in a cool, dry place. Do not store with cuff tightly wrapped.
3. Batteries: Replace when low battery symbol appears. Remove batteries if device will not be used for extended period.
4. Do not disassemble device. No user-serviceable parts inside.

CAUTION! Never wash or sterilize the cuff in an autoclave. Avoid sharp objects near cuff.

Technical Specifications

• Measurement Method: Oscillometric
• Pressure Range: 0-299 mmHg
• Pulse Range: 40-180 beats per minute
• Accuracy: Pressure: ±3 mmHg, Pulse: ±5% of reading
• Memory: 99 readings x 2 users
• Cuff Size: 22-32 cm (8.7-12.6 inches) arm circumference
• Power Supply: 4 x 1.5V AA batteries or DC 6V 500mA adapter (optional)
• Auto Power Off: Approximately 1 minute after measurement
• Operating Conditions: 10°C to 40°C, 15% to 90% relative humidity (non-condensing)
• Dimensions: Approx. 123mm (W) x 85mm (H) x 141mm (D)
• Weight: Approx. 300g (without batteries)

Troubleshooting

Reset: Remove batteries for 5 minutes, then reinsert to reset device.

Service: For technical support, contact Microlife Customer Service at 1-800-566-3456 or visit www.microlife.com.