Microlife BP3BU1-4U Blood Pressure Monitor User Manual

The Microlife BP3BU1-4U is an upper arm blood pressure monitor designed for home use, featuring automatic inflation, one-touch operation, irregular heartbeat detection, hypertension indicator, memory storage for multiple users, large LCD display, and comfortable cuff. It provides accurate systolic and diastolic blood pressure readings along with pulse rate. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main unit with LCD display, Upper Arm Cuff, 4x AA batteries, Instruction manual, Storage case.

Safety Information

Read all instructions before use. Keep for future reference.

1. Do not use on infants, children, or persons unable to express themselves.
2. Consult physician before use if you have arrhythmia, pre-eclampsia, or other circulatory disorders.
3. Do not use during physical activity or immediately after exercise.
4. Wait at least 5 minutes between measurements on the same arm.
5. Do not use in areas with strong electromagnetic fields.

WARNING! This device is not a substitute for professional medical diagnosis. Always consult your physician about blood pressure management.

Package Contents

• Main Unit: Blood pressure monitor with display
• Upper Arm Cuff: 22-42 cm circumference with Velcro closure
• Batteries: 4x AA alkaline batteries
• Instruction Manual: Complete user guide
• Storage Case: For device protection and portability
• Warranty Card: Manufacturer's warranty information

CAUTION! Check all contents upon unpacking. Contact retailer if any items are missing or damaged.

Device Overview

Front Panel: START/STOP button, MEMORY button, USER SELECT button, LCD display.

Display Symbols: Systolic pressure, Diastolic pressure, Pulse rate, Irregular heartbeat indicator, Hypertension indicator, User indicator, Memory indicator, Battery indicator, Date/Time.

Cuff Components: Air tube connector, Velcro closure, artery marker, metal ring.

Connections: Cuff connector port on left side of main unit.

Before First Use

Prepare device for initial measurement.

1. Insert batteries: Open battery compartment, insert 4 AA batteries observing polarity.
2. Set date and time: Press and hold MEMORY button for 3 seconds, use START/STOP to adjust.
3. Select user: Press USER SELECT to choose User 1 or User 2.
4. Apply cuff properly: Position cuff on bare upper arm with artery marker over brachial artery.
5. Rest before measurement: Sit quietly for 5 minutes with feet flat on floor.

Tip: For most accurate results, take measurements at the same time each day.

Taking a Measurement

Follow these steps for accurate readings.

1. Sit comfortably with back supported and feet flat on floor.
2. Place cuff on left upper arm (unless instructed otherwise by physician).
3. Position cuff 1-2 cm above elbow with tube facing downward.
4. Secure cuff snugly but not too tight (should fit one finger underneath).
5. Rest arm on table with palm up, cuff at heart level.
6. Press START/STOP button to begin measurement.
7. Remain still and quiet during inflation and measurement.
8. Read results on display when measurement completes.
9. Press START/STOP to turn off or wait for automatic shutoff.

WARNING! Do not move or talk during measurement. Ensure cuff is at heart level.

Understanding Results

The display shows systolic pressure, diastolic pressure, and pulse rate.

Irregular Heartbeat Symbol: Appears if irregular heartbeat detected during measurement. Consult physician if this appears frequently.

Error Codes: E1 (cuff too loose), E2 (movement during measurement), E3 (pressure error), E4 (pulse error).

Memory Function

Stores up to 99 measurements per user.

1. View memory: Press MEMORY button to scroll through stored readings.
2. Average value: Display shows average of last 3 measurements for current user.
3. Clear memory: Press and hold MEMORY button for 5 seconds while in memory mode.
4. User selection: Press USER SELECT to switch between User 1 and User 2 memory.

Note: Memory includes date, time, systolic, diastolic, pulse, and irregular heartbeat indicator for each reading.

Battery Information

• Battery Type: 4x AA alkaline batteries (LR6)
• Battery Life: Approximately 500 measurements
• Low Battery Indicator: Empty battery symbol appears on display
• Replacement: Replace all 4 batteries at same time
• Disposal: Dispose according to local regulations

CAUTION! Do not mix old and new batteries. Do not mix alkaline and rechargeable batteries. Remove batteries if device will not be used for extended period.

Care & Cleaning

Remove batteries before cleaning. Use only slightly damp cloth; do not immerse in water.

1. Clean cuff with mild soap and damp cloth; air dry completely.
2. Clean main unit with dry or slightly damp cloth.
3. Do not use alcohol, solvents, or abrasive cleaners.
4. Store in cool, dry place away from direct sunlight.
5. Do not fold cuff tightly; store loosely in case.

WARNING! Never wash cuff in washing machine. Do not expose to extreme temperatures or humidity.

Troubleshooting

Reset: Remove batteries for 5 minutes to reset device.

Service: For technical support, contact Microlife customer service at 1-800-******* or visit www.microlife.com