Microlife BPB1 Classic Blood Pressure Monitor User Manual

The Microlife BPB1 Classic is an upper-arm blood pressure monitor designed for home use, featuring automatic inflation, one-touch operation, large LCD display, irregular heartbeat detection, 60-memory storage with date and time stamp, WHO blood pressure classification indicator, and a wide-range cuff (22-42 cm). It is clinically validated and powered by 4xAA batteries or optional AC adapter. Below are key sections for safety, features, preparation, measurement, memory review, maintenance, and troubleshooting.

Features at a Glance

Key components: Main unit with LCD display, Wide-range arm cuff (22-42 cm), AC adapter port, Battery compartment, START/STOP button, MEMORY button.

Safety Information

Read all instructions before use. For personal home use only.

1. Do not use on infants, children, or persons unable to express themselves.
2. Consult your physician before use if you have arrhythmia, pregnancy, or other conditions.
3. Do not use near strong electromagnetic fields (e.g., microwave ovens, mobile phones).
4. Ensure cuff is properly applied; incorrect placement may cause inaccurate readings.
5. Do not inflate cuff when not wrapped around arm.

WARNING! This device is not a substitute for professional medical diagnosis. Consult your doctor for interpretation of readings.

Before First Use

Prepare the device for first measurement.

1. Insert batteries: Open battery compartment, insert 4xAA batteries observing polarity.
2. Set date and time: Press and hold MEMORY button for 3 seconds, use START/STOP to adjust.
3. Apply cuff correctly: Wrap cuff on bare upper arm 1-2 cm above elbow.
4. Rest for 5 minutes before first measurement.

CAUTION! Use only recommended batteries or AC adapter. Do not mix old and new batteries.

Specifications

• Measurement Method: Oscillometric, automatic inflation/deflation.
• Measurement Range: Pressure: 0-299 mmHg, Pulse: 40-180 beats/min.
• Accuracy: Pressure: ±3 mmHg, Pulse: ±5% of reading.
• Memory: 60 readings with date and time.
• Cuff Size: 22-42 cm arm circumference.
• Power Supply: 4xAA batteries (1.5V) or DC 6V AC adapter.
• Battery Life: Approx. 500 measurements (alkaline batteries).
• Display: LCD with backlight (if applicable).
• Operating Conditions: 10°C to 40°C, 15% to 85% humidity.
• Dimensions: Approx. 135mm (W) x 105mm (H) x 70mm (D).

Parts and Controls

Front Panel: LCD display, START/STOP button, MEMORY button. Side: AC adapter port. Bottom: Battery compartment.

Display Symbols: Systolic/Diastolic/Pulse values, Battery indicator, Memory full, Irregular heartbeat symbol, WHO color bar (Green/Yellow/Red), Date/Time, Error codes.

Buttons: START/STOP (Start measurement, Set date/time), MEMORY (Review stored readings, Enter setting mode).

Applying the Cuff

Correct cuff application is essential for accurate readings.

1. Sit comfortably with back supported and feet flat on floor.
2. Bare your left upper arm (or right if instructed).
3. Pass end of cuff through metal loop to form a circle.
4. Place cuff 1-2 cm above elbow with air tube aligned with artery (marked with arrow).
5. Wrap cuff snugly; you should fit one finger between cuff and arm.
6. Rest arm on table with palm up, cuff at heart level.

Tip: Avoid talking or moving during measurement.

Taking a Measurement

Follow these steps for reliable results.

1. Preparation: Rest for 5 minutes in a quiet environment. Avoid caffeine, exercise, and smoking 30 minutes prior.
2. Apply cuff as described in section 7.
3. Start: Press START/STOP button. Cuff inflates automatically.
4. Measurement: Remain still and quiet. Cuff deflates gradually.
5. Reading: Results display with systolic, diastolic, and pulse rate. WHO indicator shows category.
6. Irregular Heartbeat: If detected, IHD symbol appears. Consult physician if frequent.
7. Power off: Device turns off automatically after 1 minute.

WARNING! Do not inflate cuff manually. Stop measurement if pain or discomfort occurs.

Memory Function

Stores up to 60 readings with date and time.

1. Review memory: Press MEMORY button to scroll through stored readings (oldest to newest).
2. Delete all memory: In memory mode, press and hold START/STOP for 3 seconds until display clears.
3. Memory full: "FULL" symbol appears when 60 readings stored; delete old readings to store new.

Note: Memory is retained when batteries are replaced if done quickly (within 2 minutes).

Care & Cleaning

Unplug AC adapter and remove batteries before cleaning.

1. Wipe main unit with soft, dry cloth. Do not use solvents or abrasives.
2. Cuff: Clean with mild soap and damp cloth; air dry completely before storage.
3. Storage: Keep in cool, dry place away from direct sunlight and extreme temperatures.
4. Do not immerse any part in water.

CAUTION! Do not wash cuff in washing machine or use bleach.

Regulatory Information

This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that it does not cause harmful interference. CE marked according to MDD 93/42/EEC. Clinical validation according to ANSI/AAMI/ISO 81060-2:2013. Manufactured for Microlife AG, Switzerland. For support, visit www.microlife.com or contact your local distributor.

Troubleshooting

Reset: Remove batteries for 2 minutes to reset device.

Service: Do not attempt to repair. Contact authorized service center: www.microlife.com/service