Microlife BPB2 Basic Blood Pressure Monitor User Manual

The Microlife BPB2 Basic is an automatic upper arm blood pressure monitor designed for home use. It features one-touch operation, a large LCD display with backlight, irregular heartbeat detection, hypertension indicator, memory storage for up to 30 readings with date and time stamp, WHO blood pressure classification indicator, and automatic power-off. Powered by 4 AA batteries or optional AC adapter. Below are key sections for safety, features, setup, measurement, maintenance, and troubleshooting.

Features at a Glance

Key components: Main unit with LCD display, Arm cuff with D-ring, AC adapter port, Battery compartment, START/STOP button, MEMORY button.

Safety Information

Read all instructions before use. For personal home use only.

1. Do not use on infants, children, or persons unable to express themselves.
2. Consult physician before use if you have arrhythmia, pre-eclampsia, or other circulatory disorders.
3. Do not use during vehicle operation or if drowsy.
4. Keep device away from children and pets.
5. Do not disassemble or modify the device.

WARNING! This device is not a substitute for professional medical diagnosis. Always consult your physician about your blood pressure.

Package Contents

Unpack and verify all components are present.

• Microlife BPB2 Basic Monitor (1 unit)
• Arm Cuff (22-32 cm standard size) (1 unit)
• Instruction Manual (this document)
• Quick Start Guide (1 sheet)
• Storage Case (1 unit)
• Warranty Card (1 card)

Note: Batteries and AC adapter are not included in standard package (sold separately).

Device Overview

Front: LCD display, START/STOP button. Side: MEMORY button, AC adapter port. Bottom: Battery compartment.

Display Symbols: Systolic pressure, Diastolic pressure, Pulse rate, Irregular heartbeat symbol, Hypertension indicator bar, User indicator (1 or 2), Memory full indicator, Low battery symbol, Date and time.

Cuff: Cloth cuff with Velcro closure, air tube connector, artery marker (align with brachial artery).

Initial Setup

Prepare device for first use.

1. Insert batteries: Open battery compartment, insert 4 AA batteries observing correct polarity.
2. Set date and time: Press and hold MEMORY button for 3 seconds, use START/STOP to adjust values.
3. Select user: Press MEMORY briefly to toggle between User 1 and User 2.
4. Connect cuff: Insert cuff tube connector into device port until it clicks.

CAUTION! Use only recommended batteries. Remove batteries if device will not be used for extended period.

Taking a Measurement

For accurate results, follow these steps carefully.

1. Rest for 5 minutes before measurement. Avoid caffeine, exercise, and smoking 30 minutes prior.
2. Sit comfortably with back supported, feet flat on floor, arm supported at heart level.
3. Wrap cuff on bare upper arm 1-2 cm above elbow. Artery marker should align with brachial artery.
4. Secure cuff snugly but not too tight (should fit one finger underneath).
5. Press START/STOP button. Device will inflate automatically.
6. Remain still and quiet during measurement. Do not move arm or talk.
7. Reading will display when measurement is complete. Device deflates automatically.
8. Record your reading if desired. Device automatically stores it in memory.

Tip: Take measurements at same time each day for consistent tracking.

Understanding Results

The display shows systolic pressure (higher number), diastolic pressure (lower number), and pulse rate.

Irregular Heartbeat Symbol: Appears if irregular pulse detected during measurement. Consult physician if symbol appears frequently.

Memory Function

Device stores last 30 readings for each user (60 total).

1. View memory: Press MEMORY button to scroll through stored readings.
2. Delete memory: While in memory mode, press and hold START/STOP for 3 seconds to clear current user's memory.
3. Average reading: When 3 measurements are taken within 10 minutes, average is calculated and displayed.

Note: Memory full indicator appears when 30 readings are stored. Oldest reading is overwritten by new one.

Care & Maintenance

Proper care ensures accurate measurements and device longevity.

• Clean cuff with mild soap and damp cloth only. Do not immerse in water.
• Clean device body with dry soft cloth. Do not use solvents or abrasives.
• Store in provided case in cool, dry place away from direct sunlight.
• Remove batteries if device will not be used for 3 months or longer.
• Replace cuff if it becomes damaged, cracked, or fails to hold pressure.

CAUTION! Do not autoclave, sterilize, or expose to high temperatures. Do not attempt to repair device yourself.

Specifications

• Measurement Method: Oscillometric
• Pressure Range: 0-299 mmHg
• Pulse Range: 40-180 beats per minute
• Accuracy: Pressure: ±3 mmHg, Pulse: ±5% of reading
• Cuff Size: 22-32 cm (standard adult)
• Memory: 30 readings per user (2 users total)
• Power Supply: 4 x 1.5V AA batteries or 6V DC AC adapter
• Battery Life: Approximately 500 measurements (alkaline batteries)
• Dimensions: 123mm (W) x 85mm (H) x 141mm (D)
• Weight: Approximately 300g (without batteries)
• Operating Conditions: 10°C to 40°C, 15% to 90% RH (non-condensing)
• Storage Conditions: -20°C to 55°C, 10% to 95% RH

Troubleshooting

Reset: Remove batteries for 5 minutes, then reinsert to reset device.

Service: For technical support, contact Microlife Customer Service at 1-800-566-3456 or visit www.microlife.com