Microlife BPM 1 Blood Pressure Monitor User Manual

The Microlife BPM 1 is an automatic upper arm blood pressure monitor designed for home use. It features one-touch operation, a large LCD display, irregular heartbeat detection, and memory storage for multiple users. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

1. Features at a Glance 2. Safety Information 3. Package Contents 4. Device Overview 5. Initial Setup 6. Taking a Measurement 7. Understanding Results 8. Memory Function 9. Battery & Power 10. Care & Cleaning 11. Troubleshooting

Features at a Glance

Key components: Main unit with LCD display, Arm cuff with tube and connector, Instruction manual, Storage case, Batteries.

Feature	Description
One-Touch Operation	Automatic inflation and measurement
Large LCD Display	Clear readout of systolic, diastolic, pulse
Irregular Heartbeat Detection	Detects and indicates irregular heartbeats during measurement
Memory Function	Stores readings for multiple users
Automatic Power Off	Conserves battery life
WHO Classification Indicator	Color-coded bar graph shows blood pressure category
Cuff Fit Indicator	Ensures proper cuff placement
Date & Time Stamp	Records measurement time

Safety Information

Read all instructions before use.

Consult your physician before starting any blood pressure monitoring program.
Do not use on infants, small children, or persons unable to express themselves.
Do not use during or immediately after physical exercise.
Do not inflate cuff when not wrapped around arm.
Keep device away from extreme temperatures, humidity, dust, and direct sunlight.

WARNING! This device is not a substitute for professional medical diagnosis. If readings are consistently abnormal, consult your doctor.

Package Contents

Microlife BPM 1 Blood Pressure Monitor
Arm Cuff (22-32 cm standard size)
Instruction Manual
4 x AA Batteries
Storage Case
Warranty Card

CAUTION! Check all contents upon unpacking. Do not use if any part is damaged.

Device Overview

Front Panel: START/STOP button, MEMORY button, USER button (1/2), LCD display.

Display Symbols: Systolic pressure, Diastolic pressure, Pulse rate, Irregular heartbeat symbol, Battery indicator, Memory indicator, Cuff fit indicator, WHO classification bar.

Connector Port: For cuff tube connection on side of device.

Initial Setup

Insert Batteries: Open battery compartment, insert 4 AA batteries observing polarity.
Set Date & Time: Press and hold MEMORY button for 3 seconds, use START/STOP to adjust.
Connect Cuff: Plug cuff tube firmly into device port.
Select User: Press USER button to choose User 1 or User 2 for memory storage.

Tip: Wait 5 minutes after physical activity or eating before first measurement.

Taking a Measurement

Sit comfortably with back supported and feet flat on floor.
Wrap cuff on bare upper arm 1-2 cm above elbow. Tube should run down center of arm.
Position cuff at heart level. Rest arm on table.
Press START/STOP button. Device will inflate automatically.
Remain still and quiet during measurement.
Results display automatically with pulse reading.
Device deflates automatically. Press START/STOP to turn off.

WARNING! Do not move or talk during measurement. Ensure cuff is not too tight or loose.

Understanding Results

Systolic (upper number): Pressure when heart beats. Diastolic (lower number): Pressure when heart rests between beats.

WHO Category	Systolic (mmHg)	Diastolic (mmHg)	Display Color
Optimal	< 120	< 80	Green
Normal	120-129	80-84	Yellow
High Normal	130-139	85-89	Orange
Hypertension	≥ 140	≥ 90	Red

Irregular heartbeat symbol appears if irregular rhythm detected during measurement.

Memory Function

Stores up to 60 readings per user (30 each for User 1 and User 2).

To view memory: Press MEMORY button. Display shows average of last 3 readings.
Press again to scroll through individual readings with date/time.
To clear memory: Press and hold USER and MEMORY buttons simultaneously for 5 seconds.

Note: Memory is retained when batteries are replaced if done within 2 minutes.

Battery & Power

Battery Type: 4 x AA alkaline batteries (included).
Battery Life: Approximately 500 measurements.
Low Battery Indicator: Empty battery symbol appears when replacement needed.
Automatic Shut-off: Turns off after 1 minute of inactivity.

CAUTION! Remove batteries if device will not be used for extended period. Do not mix old and new batteries.

Care & Cleaning

Remove batteries before cleaning. Wipe device with slightly damp cloth. Do not immerse in water.

Cuff Care: Wipe with mild soap solution. Do not machine wash. Do not twist tube.

Storage: Store in provided case in cool, dry place. Do not store with cuff tightly wrapped.

Troubleshooting

Symptom	Possible Cause	Corrective Action
No display	Dead batteries	Replace all 4 batteries.
Error code E1	Cuff not properly connected	Check cuff tube connection.
Error code E2	Cuff over-inflated	Remove cuff and restart measurement.
Error code E3	Measurement error	Ensure proper cuff position and remain still.
Inconsistent readings	Wrong cuff position or movement	Follow measurement procedure exactly.
Memory not working	Batteries removed too long	Replace batteries within 2 minutes to retain memory.

Service: For technical support, contact Microlife Customer Service at 1-800-xxx-xxxx or visit www.microlife.com.