Microlife BPM6 Blood Pressure Monitor User Manual

The Microlife BPM6 is an automatic upper arm blood pressure monitor with advanced features for accurate home measurement. It features a large LCD display, one-touch operation, irregular heartbeat detection, 2-user memory with 99 measurements each, WHO blood pressure classification indicator, date and time display, and automatic shut-off. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main unit with LCD display, Upper arm cuff with D-ring, AC adapter, Storage case, User manual.

Safety Information

Read all instructions before use. Keep out of reach of children.

1. Do not use on infants, young children, or persons unable to express themselves.
2. Consult physician before use if you have arrhythmia, blood circulation problems, or other medical conditions.
3. Do not use during dialysis or if you have pre-eclampsia.
4. Do not wrap cuff over clothing or apply to injured arm.
5. Do not use near flammable gases or in oxygen-rich environments.

WARNING! This device is not a substitute for professional medical diagnosis. Always consult your physician about blood pressure readings.

Package Contents

• Microlife BPM6 Monitor: 1 unit
• Upper Arm Cuff: 22-42 cm (standard adult size)
• AC Adapter: 1 unit (input: 100-240V AC)
• AA Batteries: 4 pieces (for battery operation)
• Storage Case: 1 unit
• User Manual: This document
• Quick Start Guide: 1 sheet

CAUTION! Check all contents before use. Do not use if any parts are damaged.

Device Overview

Front Panel: START/STOP button, MEMORY button, USER SELECT button (1/2), LCD display. Cuff: D-ring system, air tube connector, artery marker.

Display Symbols: User indicator (1/2), Memory full, Battery low, Heart symbol (pulse), Irregular heartbeat symbol, WHO classification bar, Date/Time, Systolic/Diastolic values, Pulse rate, Cuff fit indicator.

Back Panel: AC adapter jack, Battery compartment, Air outlet.

First-Time Setup

Prepare device before first measurement.

1. Insert batteries: Open battery compartment, insert 4 AA batteries observing polarity.
2. Set date and time: Press and hold MEMORY button for 3 seconds, use START/STOP to adjust.
3. Connect cuff: Insert air tube into socket until it clicks.
4. Select user: Press USER SELECT to choose User 1 or User 2.
5. AC adapter: Plug into device and wall outlet for continuous power.

Tip: For most accurate results, use AC adapter when possible.

Taking a Measurement

For accurate readings, follow these steps carefully.

1. Rest for 5 minutes before measuring. Avoid caffeine, exercise, or smoking 30 minutes prior.
2. Sit comfortably with back supported, feet flat on floor, arm supported at heart level.
3. Wrap cuff on bare upper arm 1-2 cm above elbow. Artery marker should align with brachial artery.
4. Press START/STOP button. Device will inflate automatically.
5. Remain still and quiet during measurement. Do not move arm or talk.
6. Results display automatically with systolic, diastolic, and pulse readings.
7. Device deflates completely. Press START/STOP to turn off, or it shuts off automatically.

WARNING! Do not inflate cuff when not attached to arm. Do not exceed 299 mmHg pressure.

Memory Function

Stores 99 measurements per user with date and time.

1. Select user: Press USER SELECT to choose User 1 or User 2.
2. View memory: Press MEMORY button to scroll through stored measurements.
3. Average value: After 3 measurements, device shows average of last 3 readings.
4. Clear memory: Press and hold USER SELECT and MEMORY simultaneously for 3 seconds to clear current user's memory.
5. Memory full: "FULL" symbol appears when 99 measurements stored. Clear memory to continue storing.

Note: Memory is maintained when batteries are removed (for approximately 5 minutes).

Understanding Results

WHO Classification Indicator shows color-coded results:

Irregular Heartbeat Symbol: Appears if irregular rhythm detected during measurement. Consult physician if this appears frequently.

Care & Maintenance

Clean device regularly for optimal performance.

1. Unplug AC adapter and remove batteries before cleaning.
2. Wipe monitor with slightly damp cloth. Do not immerse in water.
3. Clean cuff with mild soap and damp cloth. Air dry completely.
4. Store in provided case in cool, dry place away from direct sunlight.
5. Replace batteries when low battery symbol appears.
6. Have device checked annually for accuracy.

CAUTION! Do not use alcohol, solvents, or abrasive cleaners. Do not autoclave or sterilize.

Specifications

• Measurement Method: Oscillometric
• Measurement Range: Pressure: 0-299 mmHg, Pulse: 40-199 beats/minute
• Accuracy: Pressure: ±3 mmHg, Pulse: ±5% of reading
• Cuff Size: 22-42 cm (standard adult)
• Memory: 2 users × 99 measurements
• Power Supply: 4 × 1.5V AA batteries or 6V DC adapter
• Battery Life: Approximately 500 measurements (alkaline batteries)
• Dimensions: 135 × 105 × 65 mm (monitor only)
• Weight: 350 g (without batteries)
• Operating Conditions: 10°C to 40°C, 15% to 90% humidity
• Storage Conditions: -20°C to 60°C, 10% to 95% humidity

Troubleshooting

Reset: Remove batteries and AC adapter for 5 minutes to reset device.

Service: For technical support, contact Microlife Customer Service at 1-800-435-XXXX or visit www.microlife.com