Microlife WatchBP Home Blood Pressure Monitor User Manual

The Microlife WatchBP Home is an automatic upper arm blood pressure monitor designed for accurate home measurement. It features clinically validated technology, an irregular heartbeat detector, a large memory capacity for multiple users, a clear LCD display with backlight, one-touch operation, and a comfortable D-ring cuff. Below are key sections for safety, features, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Main unit with LCD display, D-ring arm cuff, AC adapter (optional), storage case, and user manual.

Safety Information

Read all instructions before use. This device is for home use only.

1. Do not use on infants, small children, or persons unable to express their consent.
2. Do not use during physical activity or immediately after exercise.
3. Consult your physician before use if you have arrhythmia, pre-eclampsia, or other circulatory disorders.
4. Do not use on injured or sore arms.
5. Keep device away from children and pets.

WARNING! This device is not a substitute for professional medical diagnosis. Always consult your doctor about your blood pressure readings.

Package Contents

• Main Unit: Microlife WatchBP Home monitor
• Arm Cuff: D-ring cuff (22-42 cm circumference)
• AC Adapter: Optional power adapter (model-specific)
• Batteries: 4 x AA batteries (if included)
• Storage Case: For device and cuff storage
• User Manual: This instruction booklet
• Quick Start Guide: Basic operation instructions

CAUTION! Check all contents upon unpacking. Do not use if any parts are damaged or missing.

Device Overview

Front Panel: LCD display, START/STOP button, MEMORY button, USER button. Back: Battery compartment, AC adapter port. Cuff: D-ring closure, air tube connector, artery marker.

Display Symbols: Systolic pressure, Diastolic pressure, Pulse rate, Irregular heartbeat symbol, User indicator (1/2), Memory full indicator, Battery low indicator, WHO color bar, Date and time.

Buttons: START/STOP (begin/end measurement), MEMORY (review stored readings), USER (switch between user 1 and 2).

Before First Use

Prepare device for initial measurements.

1. Install batteries: Open battery compartment, insert 4 AA batteries observing polarity.
2. Set date and time: Press and hold MEMORY button for 3 seconds, use START/STOP to adjust.
3. Select user: Press USER button to choose user 1 or 2.
4. Apply cuff correctly: Position artery marker over brachial artery on bare upper arm.

Tip: Rest for 5 minutes before first measurement. Avoid caffeine, smoking, or exercise 30 minutes prior.

Taking a Measurement

Follow these steps for accurate readings.

1. Sit comfortably with back supported and feet flat on floor.
2. Wrap cuff on bare upper arm 1-2 cm above elbow.
3. Ensure cuff is snug but not tight; tube runs down center of arm.
4. Rest arm on table with cuff at heart level.
5. Press START/STOP button; device will inflate automatically.
6. Remain still and quiet during measurement.
7. Read results on display when measurement completes.
8. Press START/STOP to turn off or wait for auto power-off.

WARNING! Do not move or talk during measurement. Ensure proper cuff position for accurate results.

Memory Function

Stores up to 99 readings per user with date and time.

1. View memory: Press MEMORY button to scroll through stored readings.
2. Switch users: Press USER button to toggle between user 1 and 2 memory.
3. Clear memory: Press and hold MEMORY button for 5 seconds when memory is displayed.
4. Average reading: Automatically calculates average of last 3 measurements taken within 10 minutes.

Note: Memory is maintained when batteries are replaced if done within 3 minutes.

Understanding Results

Display shows systolic pressure (top), diastolic pressure (middle), and pulse rate (bottom).

Irregular Heartbeat Symbol: Appears if irregular pulse is detected. Consult physician if this appears frequently.

Care & Maintenance

Clean device with soft, dry cloth only. Do not immerse in water or use chemicals.

1. Store in provided case when not in use.
2. Keep away from extreme temperatures, humidity, and direct sunlight.
3. Replace batteries when low battery symbol appears.
4. Check cuff periodically for wear or damage.
5. Do not disassemble device; no user-serviceable parts inside.

CAUTION! Do not use if device or cuff is damaged. Contact authorized service center.

Specifications

• Measurement Method: Oscillometric
• Pressure Range: 0-299 mmHg
• Pulse Range: 40-180 beats per minute
• Accuracy: Pressure: ±3 mmHg, Pulse: ±5%
• Cuff Size: 22-42 cm (standard adult)
• Memory: 99 readings x 2 users
• Power Supply: 4 x 1.5V AA batteries or 6V DC adapter
• Battery Life: Approximately 500 measurements
• Dimensions: 135 x 105 x 65 mm (main unit)
• Weight: 350 g (without batteries)
• Operating Conditions: 10°C to 40°C, 15% to 90% humidity

Troubleshooting

Reset: Remove batteries for 3 minutes to reset device.

Service: Contact Microlife customer service at 1-800-432-8484 or visit www.microlife.com